Filter Cartridges

Placon pleated filter cartridges - PV series Placon PPV series filter cartridges are typical filters containing nominally-rated, all polypropylene pleated media for fine filtration and high efficiency widely applied in various industrial filtration processes. The design of multi-layer filter intensifies the cartridge structure to maintain a consistent filtration; the depth type main filter traps the contaminants in different depths to give large dirt holding capacity; the structure with optimized pleat height and density provides the lowest possible pressure drop and maximum service life. Placon PPV series pleated filter cartridges are entirely polypropylene of thermoplastically bonded support constructions which eliminate risk of extractable from sealing materials and offer virtually universal chemical compatibility. Placon PPV series filter cartridges are available in different micron ratings to match the flow, pressure drop, and retention requirements of most liquid and gas micron filtration applications. Applications: Acid and base solutions Etchants for semiconductor and PC board Beer, vintages, Syrups, Juices and water Solvents for electronics Photographic chemicals & Solutions Liquid and solvents for LCD manufacturing Paints, dyes and jet printer inks DI and RO water pretreatment Plating and Coating solutions Toiletries, Shampoo, Creams and Lotions Coolants, pesticides and polymers Compressed air and gases Operating Conditions • Max Operating Temperature : 82 0C (180 0F) @ 0.7 Bar (10 psid) • Max Differential Pressure : 4.14 Bar (60 psid) @ 25 0C ( 77 0F) 3.10 Bar (45 psid) @ 60 0C (140 0F) • Max Differential Reverse Pressure : 3.45 Bar (50 psid) @ 25 0C ( 77 0F) 2.76 Bar (40 psid) @ 60 0C (140 0F) • Recommended Change-out Diff. Pr. : 2.4 Bar (35 psid)

Pleated design maximizes dirt-holding capacity durable polypropylene media resists bacterial attack suitable for municipal or well applications. Nominal 1,5,10 & 30 - micron rating. Plated cartridges are manufactured from a durable polypropylene media. They are resistant to bacterial attack and compatible with a wide range of chemicals. The high porosity of the media provides higher flow rares and dirt holding, while maintaining extremely low pressure drop. The media is plated around a polypropylene core for added strength and the ends are immersed in a thermo setting vinyl plastisol. Embedding and sealing each end of the pleat block in this fashion fuses the three components together a unitized end cap and gasket. The overlap seam is conically welded to reduce internal bypass, improving filtration efficiency. Pleated cartridges provide nominal 1,5,10 & 30 - micron filtration and are highly effective at reducing medium / fine particles in a variety of residential, commercial and industrial applications.

Cartridge Specifications and Performance Data

Maximum Dimensions	Microns Rating (nominal)	Initial P (psi) @ Flow Rate (gpm)
2-5/8" x 9-3/4" (67 mm x 248 mm)	1	(<0.1 BAR@38LPM)
2-5/8" x 9-3/4" (67 mm x 248 mm)	5	(<0.1 BAR@38LPM)
2-5/8" x 9-3/4" (67 mm x 248 mm)	10	(<0.1 BAR@38LPM)
2-5/8" x 20" (67 mm x 508 mm)	5	(<0.1 BAR@38LPM)
4-1/2" x 9-3/4" (114 mm x 248 mm)

Hurricane Filter Cartridge are made of pleated polyester filter media for low pressure Drop, increased surface area and longer life.

Features

Pleated design increased surface area and contaminant removal Longer Filtration runs for fewer change - out and less maintenance Low pressure drop Designed for general water filtration purposes.

Specifications

Filter Media	Polyester
Outside Diameter	7 ¾>
Length	9-5/8", 19/1-2", 30-3/4"
Micron Rating	1,5, 10, 20, 50 micron
Temperature Range	140°F
Maximum pressure	40 psid

Placon offer Porous Sintered Filter Elements in various shaped and sizes Viz., Discs, Domes, and Hollow Cylinders for filtration of water, Air and Chemical. The separation mechanism of Filter Elements is primarily due to deep - bed filtration. The material of construction are inert polymer alloys to suit the operational conditions like fluid medium, temperature and pressure as well as high chemical resistance. The filter Elements are available in pore sizes ranging from 1-250 microns. (Nominal Rating) We will also offer and supply Filter cylinders in any other dimensions on request.

Filtrapore is a free - sintered material that produces porous plastic products with excellent filtration efficiency of fine solid particulate combined with excellent flow ability of liquids and gases. Controlled particle size distribution and a precise temperature cycle are used to produce a wide range of interconnected cell structures and specific pore size ranges. These pore structures are designed and controlled to function in a variety of applications such as filtering, wicking, diffusing or venting gases, and sound muffling.

Features and Benefits

• Lowe Cost
• Inexpensive Tooling
• Repeatable Performance - controlled porosity
• Chemical Resistant - to most acids, bases solvents and hydrocarbons
• Excellent Corrosion Resistance
• High Purity - FDA/USDA approved resins.
• High Strength, Lightweight Friendly to assembly requirements
• Dual Filtration Capabilities - acts as both a surface and depth filter
• Hydrophilic, Hydrophobic, or Self-sealing Properties

Application

• Battery first (Vents)
• Absorbent Wicking
• Catheter Vents
• Microphone Windscreens
• DNA Sampling Filters
• Industrial Filters
• Aeration
• Biomedical Filters

PPW series wound filter cartridge is widely used for removing coarse particles from process fluid. It can remove a wide range of particle size efficiently and economically. The graded pore structure design render filter cartridges high dirt holding capacity at low pressure drop. As it uses high grade filter media and high strength core it can withstand server operating and handling conditions. Features and Benefits • Micron ratings from 0.5 to 100 Micron • Polypropylene or Bleached Cotton media available for a wide range of applications • Polypropylene or stainless steel center core available High dirt holding capacity • The media and core made of FDA compliant materials • Non-foaming and no fabric release • Low pressure drop at high flow rate

Specifications

• Filter Media

• Polypropylene

• Bleached Cotton

• Fiber Glass

Core Material

• Polypropylene

• PP/Stainless Steel

• Stainless Steel

Micron Rating

• 0.5,1, 5, 10, 20, 50 and 100 Micron (Nominal) Dimensions

• 1-1/16" (27 mm) x 2 - 1/2 (63.5 mm) OD

• Length : 9-3/4", 10", 19-3/4", 20", 30", 40"

Temperature

• Polypropylene Media : 90 C (194 F) with polypropylene core

• Bleached Cotton Media: 120 C (250 F) with Stainless steel core

Typical Applications

• Food & Beverage

• RO Pre- filtration

• Potable water

• Photographic solutions

• Plating solutions

• Organic solvents

PPS series filter cartridges are made of 100% polypropylene melt blown filter media making them suitable for a wide variety of applications. They are manufactured through special process that thermally bonds pure polypropylene micro fibers with lower density at the outside surface and progressively higher density toward the center.
Features and benefits :
• graded pore structure provide maximum dirt loading 100% polypropylene construction • compliant with fda regulation 21 cfr requirement for food and beverage contact. • non-foaming, low toc content and free from binders, lubricants or ant-static agents • high flow rate, low pressure drop and long service live • economic alternative for general purpose filtration • easy disposal-incinerators to non-volatile trace ash pps series filter cartridges are available from 0. 5micron to 100 micron rating, 9. 75" to 40" length & 2 – ½' to 4-1/2" outer diameter.
Typical application
• food & beverage • ro pre-filtration • potable water • photographic solutions • plating solutions • organic solvents
End cap configuration: • no symbol: double open end industrial, cut ends • ppe: double open end, polyethylene gasket seal • pm3: soe flat closed end, external 222 o-rings • pm8: soe fin end, external 222 o-rings
pps series specifications: • filter media: pure polypropylene • micron ratings : 0. 5, 1, 5, 10, 20, 50, 75, 100 • micron dimensions ( nominal) : 63. 5 od x id 27 mm x 254 to 1016 mm • maximum differential pr. : 35 psid (2. 41 bar) at 25 c (77 f) 20 psid (1. 38 bar) at 52 c (125 f) • recommended change- out differential pressure : • 15 psid (1. 03 bar) o ring or gasket material: silicone, epdm polypropylene

Mesh Catridge is an effective reusable pre-filter which can be used in almost every filtration application as there is a need to control increasing cost of disposable type filter cartridges due to high contamination loads. These effectively remove particle ranging from 5 micron to 100 micron and useful as per ¿ filter for collection of gross contaminants. These reduce the consumption of expensive disposable type filter cartridges when used as Pre-filter and also serves as stand filter for a wide variety of application. The features and specifications are as follows:

• Material of construction (inner / outer cage ): Polypropylene, Nylon
• Material of construction (Media): Stainless Steel, Nylon
• Size : 2.5” OD x 10” Length
• 2.5” OD x 20” Length
• 4.5” OD x 10” Length
• 4.5” OD x 20” Length
• Seal material: Vinton, Silicon Buna- N
• Maximum Recommended Flow Rate : 2500 liters/ hr to 600 liters/hr (Depends upon cartridges selection)
• Maximum Differential Pressure (Clean): 0.1 kg/cm²
• Maximum Differential Pressure (Dirty) : 2.5 kg/cm²
• Micron Rating : 5 Micron onwards
• Washable type filter media
• Reusable / Regenerable media
• Excellent Chemical compatibility
• Higher Flow Rates
• Available in a wide variety of micron rating and sizes

Typical Application

• Water filtration
• Additional Pre-filtration to RO Membrane to reduce cartridge change out cost
• Discharge water
• Process Water
• Coolants of machine tools
• Cutting oils
• Inks
• Dyes and Intermediates to reduce maintenance in RO Plants and clean product water
• Photographic Solutions
• Sea water filtration
• DM Water filtration
• Domestic water filtration
• Bore well water filtration
• Paints

Placon PAC cartridges are dual - propose filters, which provide depth filtration efficacy as well as adsorption capability by its sandwich design.
The outer layer acts as a pre-filter to intercept gels and large particles that can cause premature carbon filter plugging.
The activated carbon in the middle layer feature high adsorption performance with low pressure drop.

The inner layer acts as a final filter to remove fine particles and unloading carbon then consequently ensures the constant quality of filtrates. To optimize the adsorption efficiency the customized formulas are available forspeciai orders by different rations of activated carbon types in various granularity and density. With our technical support, Placon PAC cartridges are specified to fulfill your application requirements.

Applications

• PCB Solutions
• Plating and coating solutions
• Photographic Chemicals Pre filtration of reverse osmosis
• Industrial water Treatment
• Chlorine and VOC removal
• Tastes, odors and organic pigments reduction
• Chlorinated compounds reduction

Polypropylene is used for construction purpose with Coconut shell based activated carbon in filter media. Gaskets used are made of Buna - N, EPDM (Standard),Silicone ,Viton.

Operating Conditions

• Maximum Operating Temperature : 52 C (125 F)
• Maximum Differential Pressure : 517 Bar (75 psid)
• Recommended change -out Differential Pressure 3.10 bar (45 psid)
• Collapse Differential Pressure : 6.90 Bar (100 psid)

Dimensions

• ID = 26 mm x OD 66 mm
• Gasket included
• 9 7/8" (25 1 mm)10" (254 mm), 20" (508 mm), 30" (762 mm)

In Placon some applications Grade 304L is used. Stainless steel has excellent temperature resistance and can be used up to 500 C in air or 650 C in a reducing atmosphere

Water flow (m3/min/m2) at pressure (mbar)	SRM 10U 2 mm	SRM 20U 2 mm	SRM 30U 2 mm	SRM 40U 2 mm	SRM 50U 2 mm
69	0.25	0.46	0.66	0.83	4.4
138	0.5	0.91	1	1.66	8.87
207	0.75	1.37	1.99	2.49	13.33

Typical Application Steam filtration
• Compressed air Filtration
• Corrosive and aggressive liquids and gases
• Pre filtration to micro, ultra and reverse osmosis processes
• Catalyst recovery and removal in the chemical, petrochemical, cosmetic and pharmaceutical industries Cryogenic Fluids
• Uranium hexagon fluoride gas filtration in the nuclear industry
• Filtration of molten Polyester for the manufacture of polyester film
• Filtration of molten polymers for the man made fiber industry

Features And Benefits
• Cleanable in sits or off line to provide low whole life costs
• Regenerable by back flushing to provide low whole life costs.
• It is no seam weld.
• Manufactured without the use of binders, solvents and lubricants preventing contamination.
• Sintered stainless steel powder or fiber media designed to provide desired Filtration efficiency with high permeability and strength. Low carbon 316L stainless steel media and materials to provide high corrosion resistance
• Manufactured by welding under a controlled inert atmosphere for clean weld to prevent corrosion and provide a long life.

PLACON Offering Spun Meltblown Filter Cartriges code 7 type equaluant for Doshion Type 2 and other branded filteration product. For details please contact us.

Placon introduce placon xl filter cartridges for high flow rate and very good cost effective than nominal rate of pp spun and pp wound filter cartridges.  

Placon xl high flow cartridges giving triple time then nominal cartridges.  

Capital expense of the cartridge is 30% less than the same flow rate cartridges with housing of nominal cartridges.  

Placon xl handling and time saving more than 50% than nominal cartridges.  

Presently placon xl available 20", 40" and 60" maxi flow rate of 60" is 114m3 p/hr.